CCNP Wireless 300-360 free download
CertTree is a website to provide IT certification exam training tool for
people who attend IT certification exam examinee. CertTree CCNP
Wireless 300-360 free download has strong pertinence, which can help you
save a lot of valuable time and energy to pass IT certification exam.
Our CCNP Wireless 300-360 free download
are very close true examination questions. IN a short time of using
CertTree's simulation test, you can 100% pass the exam. So spending a
small amount of time and money in exchange for such a good result is
worthful. Please add CertTree CCNP Wireless 300-360 free download in your shopping cart now.
Share some CCNP Wireless 300-360 exam questions and answers below.
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
A. Use APs with external antennas.
B. Use DoS attack on APs while measuring the throughput.
C. Use APs with built-in antennas.
D. Use a battery pack to power APs.
E. Use a drawing of the office space to draw AP and client placements.
F. Use APs with directional antennas.
Answer: C,D,E
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: A
A Cisco 7925 phone at a client¡¯s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully.
What type of messages should the phone be sending at this point?
A. H.245
B. H.323
C. MCGP
D. SCCP
Answer: D
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm.
What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?
A. The area is below the minimum threshold configured on the tool.
B. The area is below the detectable level and indicates no RF signal.
C. The area is below -100 dBm at coverage cell edge.
D. The area is below -67 dBm at coverage cell edge.
Answer: B
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.
E. Test all the customer’s wireless devices and applications to ensure they are working properly.
Answer: B,E
What is a common cause for signal attenuation?
A. Cinder block wall
B. Office window
C. Metal door
D. Glass wall
Answer: C
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clients SO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Answer: B
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.
Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
An 802.11n implementation is being discussed. Users are satisfied with the potential 300450 Mbps throughput of new 802.11n APs.
Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)
A. 450 Mbps throughput is the client max for 5-GHz radio.
B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.
C. 300 Mbps throughput is the client max for 2.4-GHz radio.
D. The remaining bandwidth is divided per device when more clients are connected to one AP.
E. 100 Mbps Ethernet switch port is a potential bottleneck.
F. Clean Air helps clear noise for 802.11n channel bonding to work.
Answer: A,C,E
An engineer must design wireless coverage in thick-walled stairwells.
Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: A
An engineer is planning for a 24 Mbps data rate for a new installation. What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services.
Which two requirements are inputs to the design? (Choose two.)
A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointe. continuous -72 dBm coverage from one access point
Answer: BD
CertTree is a website for Cisco certification
300-360 exam to provide a short-term effective CCNP Wireless 300-360
free download. Cisco 300-360 is a certification exam which is able to
change your life. IT professionals who gain Cisco 300-360
authentication certificate must have a higher salary than the ones who
do not have the certificate and their position rising space is also very
big, who will have a widely career development prospects in the IT
industry in.
Share some CCNP Wireless 300-360 exam questions and answers below.
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
A. Use APs with external antennas.
B. Use DoS attack on APs while measuring the throughput.
C. Use APs with built-in antennas.
D. Use a battery pack to power APs.
E. Use a drawing of the office space to draw AP and client placements.
F. Use APs with directional antennas.
Answer: C,D,E
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: A
A Cisco 7925 phone at a client¡¯s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully.
What type of messages should the phone be sending at this point?
A. H.245
B. H.323
C. MCGP
D. SCCP
Answer: D
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm.
What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?
A. The area is below the minimum threshold configured on the tool.
B. The area is below the detectable level and indicates no RF signal.
C. The area is below -100 dBm at coverage cell edge.
D. The area is below -67 dBm at coverage cell edge.
Answer: B
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.
E. Test all the customer’s wireless devices and applications to ensure they are working properly.
Answer: B,E
What is a common cause for signal attenuation?
A. Cinder block wall
B. Office window
C. Metal door
D. Glass wall
Answer: C
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clients SO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Answer: B
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.
Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
An 802.11n implementation is being discussed. Users are satisfied with the potential 300450 Mbps throughput of new 802.11n APs.
Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)
A. 450 Mbps throughput is the client max for 5-GHz radio.
B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.
C. 300 Mbps throughput is the client max for 2.4-GHz radio.
D. The remaining bandwidth is divided per device when more clients are connected to one AP.
E. 100 Mbps Ethernet switch port is a potential bottleneck.
F. Clean Air helps clear noise for 802.11n channel bonding to work.
Answer: A,C,E
An engineer must design wireless coverage in thick-walled stairwells.
Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: A
An engineer is planning for a 24 Mbps data rate for a new installation. What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services.
Which two requirements are inputs to the design? (Choose two.)
A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointe. continuous -72 dBm coverage from one access point
Answer: BD
CertTree is a website for Cisco certification
300-360 exam to provide a short-term effective CCNP Wireless 300-360
free download. Cisco 300-360 is a certification exam which is able to
change your life. IT professionals who gain Cisco 300-360
authentication certificate must have a higher salary than the ones who
do not have the certificate and their position rising space is also very
big, who will have a widely career development prospects in the IT
industry in.
评论
发表评论